B16 - Swap Guide. Disconnect the battery negative terminal, then disconnect the positive terminal and remove the battery, and battery tray 4. Naturally aspirated Inline Now this is the tricky part, you do not want to damage your ac lines because they are extremely expensive to replace, you need to drop the motor down at a big enough angle to clear the lines, and then you can come up with the motor, this is really hard to explain but you will realize what you have to do once you get the motor in the air, you will definitely need another person, or 2 people if you have them. If you have a dx this is basically the same but the wiring is alot more complicated, if you have an hf this is almost exact but you will need some components such as Knuckles and Hubs from other Honda vehicles. Category Commons. You just have to remove the dust ring
Acura Integra - B16 in 91 Integra - what is involved in putting a B16 SIR1 motor in a 91 Integra LS? Has anyone ever done this swap before? Thanx for your. › Hybrid Forums › HYBRID -> ED-EF / DA.
Hey guys I was wondering if any body has done a b16a dohc vtec into a integra, and can help me out. I purchased a b16a dohc vtec from.
The Japanese B18A is not considered part of the modern B-series family.
Now find the C plug, and count to the 8th connector cCool, get another butt connector and connect it to another pin that you pulled out earlier to the wire you made for the 2nd o2 sensor and add the pin to the clip. The actuator is mounted in the same fashion as the factory models and works in the same plane as the clutch release fork.
b16a dohc vtec into a 91 integra HondaSwap
I recommend you plan ahead for this, I thought my swap was going to take one weekend and it ended up taking a whole week.
BEILEID UNBEKANNTE PERSON OF INTEREST
|Hook up your clutch cable and vehicle speed sensor.
Your going to reinstall this stuff once u have the motor back in, don't worry about it for now, It will be easier to put the motor back in without the radiator and hoses and all that. Billet Replacement mount for Acura Integra. But the problem on that motor is that the cylinders were so strong they ware the piston ring out pretty fast. Also see Honda B20A engine. TalonTSi97 Videos 69, views.
Acura INTEGRA B16A Swap
Integra & ''01 Integra Type-R - b16a into a 91 integra - How much would it cost to put a b16 a into my 91 teg? I know the shift linkage, and. The B-series are a family of inline four-cylinder DOHC automotive engines introduced by The one used for B16 and B17 engines (except for B16B) has a deck height of Honda Integra XSi; Honda CRX SiR (EF8).
Getting parts is not really an issue.
The actuator is mounted in the same fashion as the factory models and works in the same plane as the clutch release fork. Hook up your fuel lines, I had to use some pieces off of my stock motor you might also, now you should hook up your vacuum hoses but I will save that one for last. To start viewing messages, select the forum that you want to visit from the selection below.
And if I should use the b18 auto tranny or use the b16a 5 speed tranny. I got permission from Brandon aka "Hero" to post his swap guide here.
This guide is meant for swapping a b16a into a model CRX Si. .
B16 in 91 Integra HondaTech Honda Forum Discussion
Distributor Cap and Rotor Integra non-VTEC kit from Acura (''
Refer to the picture below After you are done with this you need to disconnect the linkages off of dseries motor, you will need a punch and a hammer, you will have to hammer this little pin out, this is a pain in the ass and then once its out there is one more bolt and you are done with the linkages.
It's basically the b20a5 but a little stronger.
Video: B16 in 91 integra 40 Roll B16A Powered Integra
Drain the coolant from the radiator into pan. Billet Mount Kit for Honda Civic. Use this guide at your own risk.
Yes, my password is: Forgot your password?